Fender ultimate chorus dating self consolidating concrete testing

437 volts); this may have gotten higher after 1971, but into the summer of 1971 I'd expect the plate voltages on 6CA7s to be down substantially from the YBA-1A; have the chassis sliding-in ala Fender.

fender ultimate chorus dating-25

Features silvery grey grille cloth Yorkville [...] owns Dyna-Bass #0011 and [has] used it as a promotional tool.

Sound - Reliability - Price CAD $395 [used], condition unknown, Scarborough, Ontario, Canada, February 7, 2001 Very hard to find. Dyna-Bass, front view, angle (apparently the same as the following) 1963 Dyna-Bass, serial number 0011, front view, angle Features Two channels, deep (bass), and bright (guitar); each has an attenuated and a normal gain input (like the old Marshalls); no reverb Volume control channel one, channel two; treble, bass, low range expander, high range expander (passive); the low range expander may sound like a mid-range, the hi range expander may sound like presence (on Marshalls or Fenders) to some (the section is a virtual clone of that of the Marshall JTM-45); standby switch; pilot light; ground and on/off switch; no fan One main speaker output, impedance is not indicated (runs fine using a cab of eight ohms, also often operated with four ohm loads), one "extension" speaker output also without indicated impedance.

Reliability It's a risky proposition for repairs Old and still going strong Price I bought my YBA-1A [used] about 15 years ago for $62 USD.

[...] The 2nd [used] one I bought off ebay [for] $235 USD was totally moded for guitar with extra pots on the back [...].

More power and punch than Fender, less ruggedness than Marshall.

I'd say its closer to a Vox type sound, but if you want Vox sound, this will not suffice.

A YBA-1 has a nominal 8 ohm output, and the two speaker jacks are wired in parallel.

Runs on less than 440 volts, weighs 39 pounds Dimensions: 8"x18"x10" (HWD); weight: 40 lbs. (source: Catalog) Silvery grey grille cloth; Original layout was very close to the tweed Bassman and the Marshall JTM-45 50-watt models; noticably huge big heavy transformers are a Traynor hallmark in these units up till the approximately 1972 models; Early models were tube rectified (5AR4) and used two 7027A power tubes.

] 0 [used], very early model, the serial number is 0278, which places it in 1966, uses 6CA7 tubes as specified in the tube chart, no tube rectifier, and the marshall style phenolic turret board, also, it has the hole in the chassis for the tube rectifier socket, but it is blocked with a circular steel plate, the 5 volt rectifier heater winding at the power tranny is cut about 2 inches out, December 1998 Rating Very good one. I have a 1977 YBA1 with a matching YT-15 cabinet [...]. It's probably not worth a tird as a collector's item but this amp really screams. I rate my YRM-1 second to my YBA-1, because it does not have as much balls.

This must have been one of the last real Traynor amps made... Also, my YBA-1 sounds great at all volumes, including low setttings. 1965 or 1966 YBA-1 Bass-Master (old wrap-around style case), logo 1965 or 1966 YBA-1 Bass-Master (old wrap-around style case), front view, angle 1965 or 1966 YBA-1 Bass-Master (old wrap-around style case), front view 1965 or 1966 YBA-1 Bass-Master (old wrap-around style case), back view 1966 YBA-1 Bass-Master, chassis 1966 YBA-1 Bass-Master, wiring 1968 YBA-1 Bass-Master (serial number 2xxx), front view, angle 1968 YBA-1 Bass-Master (serial number 2xxx), front view 1968 YBA-1 Bass-Master (serial number 2xxx), logo YBA-1 Bass-Master, catalog page YBA-1 Bass-Master, catalog page YBA-1 Bass-Master, schematic 10/1966 YBA-1 Bass-Master, schematic 6/1971-1974 YBA-1 Bass-Master, schematic 5/1974 - Please note: This schematic has a serious error in it.

These mods are worth doing to any Signature/Bass-Master, IMO.

Tags: , ,